PTZ RS485 dip switches for MLP1, MLP2, Pelco D & Pelco P protocols

Pelco Operation By PIH-7622/35

LILIN PIH-7622/7635 Fast Dome Set Up:

RS-485 Interface Setting and DIP SWITCH Setting:

(Please refer to PIH-7622/35 Instruction manual > Fast Dome Camera Set Up > DIP Switch Setting)

1. RS-485 IN-TML RES.       :RS-485 Input Terminal Resistance ON/OFF

2. RS-485 OUT-TML RES.   :RS-485 Output Terminal Resistance ON/OFF

3. HALF / FULL                               :HALF means 2-Line HALF DUPLEX; FULL means 4-Line FULL DUPLEX

4. BAUD SEL1                                :BAUD Rate Selection 1

5. BAUD SEL2                                :BAUD Rate Selection 2

6. PROTOCOL SEL1                       :Protocol Selection 1

7. PROTOCOL SEL2                       :Protocol Selection 2

8. PROTOCOL SEL3                       :Protocol Selection 3

9. PROTOCOL SEL4                       :Protocol Selection 4

10. Reserved

          RS-485 Input/Output Terminal Resistance Setting

☞In serial system, MUST turn the Dip Switch of RS-485 input/output terminal resistance to ON position.

☞In parallel system, MUST turn the resistance of the first and last terminal to ON position, and the resistance of nodes in-between to OFF position. This will insure the transmission interface in best condition. 。

          RS-485 Transmission Mode Selection

DIP   SWITCH

3

2-Line   HALF DUPLEX (HALF)

OFF

4-Line   HALF DUPLEX (FULL)

ON

          Transmission Rate Selection

BAUD RATE SELECTION

DIP   SWITCH

5

4

2400   bps

ON

ON

4800   bps

ON

OFF

9600   bps

OFF

ON

19200 bps

OFF

OFF

 


Protocol Selection

PROTOCOL   SELECTION

DIP SWITCH

9

8

7

6

MLP2 (MERIT   LILIN Protocol 2)

ON

ON

ON

ON

MLP1 (MERIT   LILIN Protocol 1)

ON

ON

ON

OFF

PELCO D

ON

ON

OFF

ON

PELCO P

ON

ON

OFF

OFF

 

Note:MLP1 (MERIT LILIN Protocol 1) applies in PIH-717/PIH-700/PIH-7600/PIH-7625 series.

           MLP2 (MERIT LILIN Protocol 2) applies in PIH-7603/PIH-7610/PIH-7622/PIH-7635 series.

          RS-485 Interface ON/OFF Setting

DIP SWITCH

10

9

8

7

6

5

4

3

2

1

MLP2 Version

OFF

ON

ON

ON

ON

OFF

ON

OFF

ON

ON

MLP1 Version

OFF

ON

ON

ON

OFF

OFF

ON

OFF

ON

ON

PELCO D

OFF

ON

ON

OFF

ON

ON

ON

PELCO P

OFF

ON

ON

OFF

OFF

                 ▲:Please refer to the above instruction

          Dome Camera ID SW

PELCO  D  Protocol Using:

DIP SWITCH

8

7

6

5

4

3

2

1

CAMERA ID 1

ON

ON

ON

ON

ON

ON

ON

OFF

CAMERA ID 2

ON

ON

ON

ON

ON

ON

OFF

ON

CAMERA ID 3

ON

ON

ON

ON

ON

ON

OFF

OFF

CAMERA ID 4

ON

ON

ON

ON

ON

OFF

ON

ON

CAMERA ID 5

ON

ON

ON

ON

ON

OFF

ON

OFF

 

CAMERA ID 253

OFF

OFF

OFF

OFF

OFF

OFF

ON

OFF

CAMERA ID 254

OFF

OFF

OFF

OFF

OFF

OFF

OFF

ON

 

 

 

PELCO  P  Protocol Using:

DIP SWITCH

8

7

6

5

4

3

2

1

CAMERA ID 1

ON

ON

ON

ON

ON

ON

ON

ON

CAMERA ID 2

ON

ON

ON

ON

ON

ON

ON

OFF

CAMERA ID 3

ON

ON

ON

ON

ON

ON

OFF

ON

CAMERA ID 4

ON

ON

ON

ON

ON

OFF

OFF

OFF

CAMERA ID 5

ON

ON

ON

ON

ON

OFF

ON

ON

 

CAMERA ID 31

ON

ON

ON

OFF

OFF

OFF

OFF

ON

CAMERA ID 32

ON

ON

ON

OFF

OFF

OFF

OFF

OFF

 


  OPERATION

PELCO D MPT9500 Keyboard to Control PIH-7622:

  1. First enter the CAMERA ID to be called : “number” + 【RECV ADDRS】。
  2. MANUAL OPERATION:

Joystick Control:Move the Joystick to bring the PTZ to the desired view position.

ZOOM Control:

Push【ZOOM WIDE】:Zoom out (View angle becomes wider),stops when the key released.

Push【ZOOM TELE】:Zoom in (View angle becomes narrower),stops when the key released.

FOCUS Control:

Push【FOCUS NEAR】:The target will become nearer. Focusing stops when the key released.

Push【FOCUS FAR  】:The target will become farer. Focusing stops when the key released.

IRIS Control:

Push【IRIS OPEN 】:Open the iris and brighten the picture. Iris will stop when the key released.

Push【IRIS CLOSE】:Close the iris and reduce glare.  Iris will stop when the key released.

  1. RETURNING TO A PRESET:

Push【Preset position number + PRESET GO】,PTZ will move to the preset position.

  1. PRESET NUMBER DEFINE:

PRESET 33:FLIP

PRESET 34:Return Home Position

PRESET 94:Remote Reset

PRESET 95:Menu Entry

PRESET 96:Stop Auto-Pan

PRESET 99:Startup Auto-Pan(execute auto mode item)

  1. SETTING A PRESET:

Push 【Preset position number + PRESET SET】,PTZ will store the current position and lens condition into memory.

  1. Startup Auto-Pan:

Push【PAN AUTO】to execute auto mode item.

  1. STOP Auto-Pan:

Move【JOYSTICK】to stop Auto-Pan function or push【MANU PAN】.

  1. MENU MODE:

Push【number 95 + PRESET SET】to enter PTZ menu to do the settings.

Move the joystick “up” and “down” to selection function. Move the joystick “right” and “left” to change the settings.  Push【IRIS OPEN】in menu homepage to store the setting changes or continue to another page.  Push【IRIS CLOSE】in menu homepage to leave the settings.

8. Other settings please refer to LILIN instruction manual.

 

For a full list of camera ID's for all supported protocols, please click here

 

Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

0 Comments

Article is closed for comments.